TRANSFORMER OIL TEST SERIES

  • Colorimeter

    Colorimeter

  • Distillation Tester

    Distillation Tester

  • Flash Point Tester

    Flash Point Tester

  • Gas Chromatograph Tester

    Gas Chromatograph Tester

  • Lubricating Abrasion Tester

    Lubricating Abrasion Tester

    Switch on the power, start the motor. Using an oilstone stained with ordinary lubricants completely polished shaft sleeve, press evenly oilstone with your thumb when polished, wipe motor shaft sleeve after polished, stop the motor. The purpose of polished is to eliminate the impact of original film or nanometer film on the experimental results. 1. Fix the friction block into the short lever groove of the testing machine,add ordinary lubricant oil into oil box, well-installed the lubricating oil box and the length of the lever. 2. Start the motor, firstly, let the motor run.Then at set intervals (such as 10 seconds), plus the weight on long lever ends one by one, each weight is equal to the pressure of the friction pair carrying 100 kg. Record the number of weights, look at change in ammeter pointer, the pointer increase, power consumption increase, fuel consumption also increase. Noise increases, continue to add weight (about 3,4 blocks) until the wheel stops, the machine locking, quickly turn off the power. Remove the weights, remove the short lever, observe the depth, area and roughness of grinding marks on cylindrical grinding block. 3. Choose a different angle on the grinding block to install leverage. Polish shaft sleeve again,it need to polished flat because the wear in just experiment . 4. Add our wear-resistant lubricating oil into oil box. 5. Plus the weight on long lever ends one by one, one, two …… Ordinary oil plus about four, the machine will be locked, but our wear-resistant lubricants plus more than four, the machine still operate as usual. Look ammeter pointer, only slightly move a little. Current × voltage = power consumption, ammeter pointer changes very little,power saving is fuel saving. Gradually add weight to 12, the machines also operate as usual 6. Remove the oil box, the machine operate as usual. Nano films do exist, turn off the machine switch. 7. Put down the grinding block to compare with previous grinding marks. (The testing machine equipped with our infrared thermometer can make oil temperature experiment: The steps are: put the grinding block horizontally, plus three weights on the long pole, heat the oil to boiling, note the time from the start heating to boiling , the longer of the time, the better quality of the oil.) Every time change the oil must use an oilstone stained with ordinary lubricants to polish shaft sleeve clean.If not clean, the machine will shake and accompanied by noise, affect experimental results.

  • Oil Acidity Tester

    Oil Acidity Tester

  • Oil BDV Tester

    Oil BDV Tester

  • Oil Filter

    Oil Filter

  • Oil Interfacial Tension Tester

    Oil Interfacial Tension Tester

  • Oil Moisture Tester

    Oil Moisture Tester

  • Oil Tan Delta Tester

    Oil Tan Delta Tester

  • Oil Viscosity Tester

    Oil Viscosity Tester

  • Particle Counter

    Particle Counter

    I.Description HZJS-1B Oil Particle Counter adopts Laser Extinction Technology, is designed to measure the particles’ size and quantity in oil liquid. It is Suitable for tests of pollution degree of solid particles in hydraulic oil, lubricating oil, fire resistantoil, insulating oil, turbine oil, organic liquid and polymer solution, etc. So our instrument can be used…

  • PH Value Meter

    PH Value Meter

    HZDS211 potentiometric titration automatic pH value meter is based on GB/T 7304-2000 Petroleum Products and Lubricants Acid Value Determination Method (Potentiometric Titration Method) equivalent to ASTMD664, SH/T0251-2004 and other standards to set the acid value of petroleum products and lubricants It is designed according to standards such as base value determination method (color indicator method)…

Nhắn Messenger Chat Zalo Gọi 0969326661